Kwikset SmartCode 913 Programming and Troubleshooting Guide

Introduction

Kwikset SmartCode 913 is a great smart deadbolt lock. It’s easy to use, affordable, and fairly secure. This guide will cover the basics of Kwikset SmartCode 913 programming and troubleshooting so you can set it up quickly!

Kwikset smartcode 913 programming

Kwikset SmartCode 913 programming allows you to control when and how your Kwikset SmartCode 913 works, including changing user code and master code, deleting user code, adding user code, and factory resetting your Kwikset SmartCode 913 lock.

Please note: For extra security, we hope you can enable the master code for your Kwikset SmartCode 913. And if you enable the master code, almost all programming processes will need you to enter the master code first.

Enabling and Setting the Master code on Kwikset SmartCode 913

1. Keep the door open. Press and HOLD the Program button until the keypad flashes green (about 5 seconds).
2. Enter new Master code.
3. Press the Lock button once.
4. Re-enter the Master code.
5. Press the Lock button once.

Kwikset smartcode 913 change code

Please note you can not change the user code on your Kwikset SmartCode 913 directly; you will have to delete the code you want to change first, then add a new user code to finish changing the user code on Kwikset SmartCode 913.

For more information about changing the Kwikset SmartCode 913, please check this article: How To Change Code On Kwikset SmartCode 913?

Please note that ShineACS Locks is just writing the Kwikset SmartCode 913 programming and troubleshooting article with possible handling suggestions, not offering after-sales service. If you can’t finally solve your problem with our article content, please get in touch with the Official aftermarket.

However, if you want to replace your current door locks for added security, Try our smart keyless door locks for convenience and peace of mind without any changes when installation.

Kwikset smartcode 913 delete code

To delete a code from your Kwikset SmartCode 913, you can follow the steps below:

1. Keep the door open. Press the Program button once. The keypad will flash green, and you will hear three beeps.
2. Press the Lock button once.
3. Enter the Master code.
4. Press the Lock button once.
5. Enter the user code to be deleted.
6. Press the Lock button once.
7. Re-enter the user code to be deleted.
8. Press the Lock button once.

Kwikset 913 delete all codes.

To delete all codes from the Kwikset SmartCode 913, follow these steps:

1. Keep the door open. Press the Program button once. The keypad will flash green, and you will hear three beeps.
2. Press the Lock button once.
3. Enter the Master code.
4. Press the Lock button once.
5. Press the “9” button six times.
6. Press the Lock button once.
7. Press the “9” button six times.
8. Press the Lock button once. If programming is successful, the keypad will flash green once with no beep. If programming is unsuccessful, the keypad will flash red three times with three beeps. Ensure you enter a valid Master code in step 3 during your next attempt.
9. Press the Lock button while the door is open and unlocked. If the latch bolt does not extend to the lock, all codes have been successfully deleted.

Kwikset smartcode 913 add code

To add a user code to Kwikset SmartCode 913, follow these instructions:

1. Keep the door open. Press the Program button once. The keypad will flash green, and you will hear three beeps.
2. Enter the Master code.
3. Press the Lock button once.
4. Enter the new user code.
5. Press the Lock button once.

Kwikset smartcode 913 reset master code

To factory reset Kwikset SmartCode 913 master code:

1. Remove the battery pack.
2. Press and HOLD the Program button while reinserting the battery pack. Hold the button for 30 seconds until the lock beeps and the status LED flashes red.
3. Press the Program button once more. The lock has been reset when the LED flashes green, and you hear one beep.
4. Perform the door-handing process again to teach the lock the door’s orientation and add user codes to your lock.

For more information about resetting Kwikset locks, please check this article: How To Reset Kwikset Lock Code Without Key?

Kwikset smartcode 913 auto lock

Using the Kwikset SmartCode 913, you can set your door to lock automatically and re-lock the door 30 seconds after unlocking. This is a great feature if you often forget to lock your doors when you leave or go inside. The auto-lock feature will ensure that your door locks itself, and no one can get in unless they have the code.

To activate the SmartCode 913 auto-lock feature:

• Remove the battery cover and battery pack from the interior assembly.
• Find the switches on the back panel.
• Turn the “switch 2” on

Now, the SmartCode 913 auto-lock feature has been activated.

Disabling and Deleting the Master code on Kwikset SmartCode 913

You can disable and delete the master code on your Kwikset SmartCode 913 with the following steps:

1. Keep the door open. Press and HOLD the Program button until the keypad flashes green (about 5 seconds).
2. Press the Lock button once.
3. Enter the Master code.
4. Press the Lock button once.
5. Re-enter the Master code.
6. Press the Lock button once. If programming is successful, the keypad will flash green once with one beep. If programming is unsuccessful, the keypad will flash red three times with three beeps. Please make sure the Master code has been enabled before trying to turn it off. Attempt this procedure again and enter the same Master code in steps 3 and 5.
7. Ensure switch #3 is on, and press the Program button once. If you don’t immediately hear three beeps and see the keypad flash green, the Master code is disabled. Note: The lock will time out after five seconds.

Set locking and unlocking directions for Kwikset SmartCode 913

Caution: Your lock will not function properly if this step is not completed. To set locking and unlocking direction for your Kwikset SmartCode 913:

• Install 4 AA batteries in the battery pack.
• Make sure the door is open and the latch is extended.
• Press and hold the Lock button. Do not release.
• Insert the battery pack and continue holding the lock button
• The latch bolt will retract and extend to learn the locking and unlocking direction of the door.
• Status LED will indicate success or failure
• Success: Led flashes green
• Failure: Led remains solid red

Note: The latch bolt will only retract halfway.

For more information about Kwikset SmartCode 913 programming, you can check the following video for your reference:

Kwikset SmartCode 913 Programming With a Mastercode

Also, if you want to learn how to program Kwikset SmartCode 913 without a master code, you can check this video:

Kwikset SmartCode 913 Programming Without a Master Code

Kwikset 913 troubleshooting

So you’ve got a Kwikset 913 and have problems with your locks? Maybe it’s not functioning as it should, or Kwikset SmartCode 913 stopped working. We’ll cover the most common Kwikset SmartCode 913 issues here and help get your lock working like new again.

The Common Kwikset SmartCode 913 issues include:

• Kwikset SmartCode 913 flashing red light
• Kwikset SmartCode 913 keypad light is not working
• Kwikset smartcode 913 wont lock
• Kwikset SmartCode 913 won’t unlock
• Kwikset SmartCode 913 keeps locking
• kwikset smartcode 913 lock button not working
• Kwikset SmartCode 913 stopped working

Kwikset SmartCode 913 flashing red light

If your Kwikset Smartcode 913 is flashing red, please check the following reasons and solutions why your Kwikset SmartCode 913 is flashing red light:

• Keypad flashes red once with one beep: The door jammed while attempting to lock. Manually re-lock the door. If needed, reposition strike.
• Keypad flashes red three times with three beeps.
  • Unsuccessful programming. Attempt the programming procedure again.
  • One incorrect code was entered. Re-enter code.
  • No user code programmed. Program at least one user code.
• Keypad flashes red ten times with ten beeps: Low battery. Replace batteries.
• The lock beeps two times, or the keypad flashes red three times: Programming timeout. Attempt the programming procedure again, making sure not to pause for more than 5 seconds.
• Keypad flashes red 15 times with 15 beeps. Three incorrect codes are entered within one minute. Re-enter code after 60-second keypad lockout.

Please note: The beeping sound will only be heard if switch #3 is on.

Kwikset smartcode 913 solid red light.

• The lock interior is not mounted perpendicular to the ground. Remount lock interior assembly as illustrated in the Kwikset deadbolt Installation Guide.
• The hole in the door is misaligned. Disassemble the lock and reinstall it without the adapter ring on the exterior side of the door.
• The battery level is too low. This is indicated by the keypad flashing red three times with three beeps. Use a fresh set of batteries, and perform the door-handing process again.
• The latch and strike are misaligned, causing the latch to bind. If you have not done so, perform the door-handing process while the door is open. If it is successful only when the door is open, the latch and strike are not aligned as they should be.

Kwikset SmartCode 913 keypad light is not working, or the keypad is unresponsive.

If your keypad light doesn’t work, it could be because of one of the following reasons:

• Check the battery. Please make sure they are fresh and inserted correctly. The lock will not work with dead batteries or improperly inserted batteries.
• Make sure there is no damage to your keypad. Press each key on the keypad (one at a time) and listen for a beeping sound. If no beeping is heard, this is a keypad error. Contact Technical Support for further troubleshooting.
• Check the connection between the battery and keypad: Check if anything obstructs or dislodges inside your lock that would prevent power from reaching its components properly.
• Ensure that none of these components have been damaged during installation because they could cause issues later on down the line when trying to operate them manually.
• Keypad lockout: If three incorrect codes were entered within one minute, the keypad would lock for 60 seconds.

kwikset SmartCode 913 wont lock

If your door lock’s deadbolt isn’t locking, try these troubleshooting steps:

• Check the battery. Remove the battery to see if it’s drained. If so, replace 4 AA batteries with new ones and try again (it’s important to use the same type of batteries).
• Double-check that you’ve installed your new batteries correctly. Ensure they’re installed in a matching orientation (i.e., + side up/down) and not touching each other or any metal component on the lock mechanism.
• Check battery contacts. Ensure there isn’t any corrosion or damage on either end of your Kwikset SmartCode 913 deadbolt’s circuit board or any other part where its components are connected (e.g., hinges). If there is any corrosion or damage, clean these areas thoroughly before reassembling everything back together!
• The latch and strike are misaligned, causing the latch to bind. If it is successful only when the door is open, the latch and strike are not aligned as they should be. Ensure door preparation is following the door drilling instructions.

Kwikset SmartCode 913 won’t unlock.

If your door doesn’t unlock, check the following:

• Make sure the door latch is fully engaged. That could be why your SmartCode 913 won’t unlock if it’s not.
• Check the hinges on your door frame and ensure they’re in good shape. If one is loose or broken, it could prevent proper engagement of the SmartCode 913 during unlocking.
• Check that there isn’t debris between the frame and frame jamb that prevents a seal from being made between them when they close together. This would allow water to get trapped against an exterior finish, which can cause swelling and warping over time (which will prevent proper operation).
• Check the batteries. Make sure the batteries are new and installed correctly.
• Check your keypad if that doesn’t work; it might also be damaged, so try replacing it if this option is!
• Check your user code. Make sure you are using the correct user code to open the door.

Kwikset SmartCode 913 keeps locking.

If you find that your SmartCode 913 keeps locking and unlocking, there are several possible causes:

• The extended deadbolt lock was hitting the back of the drilled frame, So when it locked, it did not fully extend, and it thought it was not locked and would try every 30 seconds again.
• The internal assembly may be screwed down too tight to allow enough movement play, causing problems while using this device.
• The door strike is not installed correctly (i.e., the bolt is too far back). You must adjust this by loosening or tightening the screws where they meet with your door’s frame.

kwikset smartcode 913 lock button not working

Suppose your SmartCode 913 lock button is not working. The following are the possible reasons and solutions:

• No user codes are programmed: The lock button will not lock the door if no codes are in the lock. Program at least one user code and test the Lock button again.
• The door-handing process was not executed: Perform the door-handing process, following the instructions inside the installation guide.
• The battery is too low to lock the door: This is indicated by the keypad flashing red three times with three beeps. Remove the batteries and replace them with a fresh set.
• The mounting plate is placing tension on the torque blade:
  • Attempt to lock and unlock the door with the key. Remove the interior assembly from the mounting plate if it cannot rotate.
  • Test the key again. If it cannot rotate, loosen the screws on the mounting plate and reposition it so there is no tension on the cylinder torque blade.

• • Ensure the latch bolt can operate smoothly with the key and reinstall the interior assembly.
• The clutch is disengaged:
  • Remove the battery pack. Remove the interior assembly from the door. Verify that the lock can be operated smoothly with the key while the interior is removed. Attempt to rotate the turn piece on the interior assembly to the vertical position. The clutch becomes disengaged if it cannot rotate to the vertical position.
  • Place the battery cover onto the interior assembly and align the turn piece with the shaft. Rotate the turn piece 180° clockwise (you will need to use force when rotating it, and you will hear it click). This will re-engage the clutch.

• • Align the turn piece with the torque blade and reinstall the interior assembly on the door.

For more Kwikset SmartCode problems and troubleshooting, please visit the Detailed Kwikset SmartCode Deadbolt Troubleshooting Guide.

Kwikset SmartCode 913 user manual

For more information about Kwikset SmartCode 913 programming and troubleshooting, you can download and check the following Kwikset SmartCode 913 user manuals:

• Kwikset SmartCode 913 User Manual PDF
• Kwikset SmartCode 913 troubleshooting Manual PDF

Conclusion

We hope this post has helped you with programming and troubleshooting your Kwikset SmartCode 913. If these tips don’t work, please get in touch with ShineACS Locks, and we’ll try to help.

For more information about Kwikset lock troubleshooting:

1. Kwikset Halo Troubleshooting
2. Kwikset Kevo Lock Troubleshooting
3. Kwikset Powerbolt 2 Troubleshooting
4. How to Rekey A Kwikset Lock?
5. How to Remove a Kwikset Deadbolt?
6. How To Change Code On Kwikset Smartcode 913?
7. How To Change Code On Kwikset SmartCode 909?